BID SPECIFICATIONS
GYM FLOOR COVER FABRIC

1. COVER REQUIREMENTS & SIZING

GymGuard™ PVC coated polyester fabric as made by CoverSports USA. The area to be
covered is ____ft. x ___ft. This will require sections ___ft, x ___ft
Color:__________.

2. FABRIC SPECIFICATIONS

• Overall Weight ____(oz./sq.yd.)
• Tear Strength warp___Ibs x fill___Ibs (per ASTM D 2261)
• Tensile Strength warp___Ibs x fill___Ibs (per ASTM D5034)
• Adhesion ___Ibs (per ASTM D751)
• Flame Resistance 2 seconds maximum (NFPA-701 small scale 1989) Must also comply with Calif, Fire Marshall. Boston Fire Marshall, UL Labs UL-214, and MIL-C-20696
• Must be anti-fungal, rot and mildew resistant

3. FLOOR COVER CONSTRUCTION

Fabric sections shall be thermally welded with an approximate 1" wide heat-seal seam, meeting the seam strength requirements In MIL-T-82288-B,

4. WARRANTY

__Years pro-rata against material defects and seam workmanship equivalent to Coversports warranty,

5. SAMPLER

A minimum 6" x 6" sample shall accompany the bid.

6. BIDDER QUALIFICATIONS

The bidder shall supply a list of at least 8 similar installations in the past year, including name, contact person, and telephone/fax numbers.

BID SPECIFICATIONS
GYMGUARD™ MOBILE STORAGE RACK FOR GYM FLOOR COVERS

1. RACK REQUIREMENT

• ___Rack(s) as manufactured by CoverSports USA to hold ___..sections of GymGuard floor covering

2. STORAGE RACK CONSTRUCTION

• Size - 34 1/2" wide x 12' 6" long x 67" high**
• End sections - 11 guage steel A frame type
• Center supports section - 14 guage round support pipes connected by 3/4" x 1/4"steel support trusses - mig welded
• Brackets - All steel with Delrin roller bearings and mig welded to end sections
• un-roll Clips - each bracket shall have a steel flap to prevent the fabric pipes from un-rolling
• Safety Roll Lock - each bracket shall have a steel Safety Roll Lock Device to prevent the steel pipes from accidentally popping out, falling out, or accidentally getting caught in the bracket
• Steel roll-up pipes -14 guage galvanized steel with one guide pin at each end
• Fabrc clips - 3 plastic clips to hold fabric securely to the roller
• Hand cranks - 2 brushed aluminum cranks to be supplied for fabric wind-up
• Wheels - 8" diameter urethane non-marring type with foot locks on each wheel

3 WARRANTY-10 years pro-rata

4. WEIGHT CAPACITY - 4800 Ibs,

Mini-Storage Rack length is 6'4"
Mini-Storage Rack length is 6'4"

BID SPECIFICATIONS
GYMGUARD™ BRUSH ASSEMBLY

1. REQUIREMENT

An adjustable brush assembly to sweep debris from the topside
Of gym floor cover fabric as it Is wound onto the mobile storage rack.

2. BRUSH ASSEMBLY PROPERTIES

• Housing - A steel housing that fits inside the frame of the mobile storage rack and is adjustable. The housing can be attached easily to either side of the rack with wing nuts.
• Brush - 144" in length consisting of black nylon 66 bristles with an overall trim length of 4 inches. The brush has an aluminum spline that is fastened to the steel housing.

3. Warranty

• 5 yeans pro-rata

BID SPECIFICATIONS
GYMGUARD™ TAPE & DISPENSER/APPLICATOR

1. TAPE REQUIRMENTS

___ Rolls of GymGuard tape as sold by CoverSports USA.

2. PROPERTIES

Width/Length - 3 inch wide X 36 yds/roll
Film Type - 5 MIL PVC, single use type
Adhesive - will leave no residue on the fabric or flooring surfaces.

3. CASE SIZE

16 Rolls packed standard per case.

4. TAPE DISPENSER

A hand-held plastic applicator to hold the 3" GymGuard tape

5. TAPE APPLICATOR

A walk-behind tape applicator to facilitate easy application of 3" GymGuard tape in order to secure the GymGuard fabric to the floor or to two overlappino sections.